Bathroom and Kitchen Sealant

Available colours
White
Colour indications are a guide only
Buy now
BUY NOW
Features and benefits

Features and benefits

A long-lasting, white bathroom and kitchen sealant
Perfect for use in areas prone to moisture and frequent wetting
Provides a waterproof seal around baths, sinks, showers, and kitchen and utility units
Mould resistant
Won't stain, blacken or yellow
Waterproof
Suitable for use on glass, stainless steel, ceramics and plastic baths and fittings
Suitable for indoor use only
Resists mould
Waterproof
Easy to apply
Interior

EVO-STIK Bathroom and Kitchen Sealant is a long-lasting, easy-to-apply white silicone sealant for use around baths, sinks, showers, and kitchen and utility units. It creates a flexible, waterproof seal that helps prevent leaks in areas exposed to moisture, frequent cleaning and condensation. 

This kitchen and bathroom silicone resists mould growth thanks to its built-in fungicide, making it ideal for maintaining a clean, hygienic finish in your home for years to come. 

As a white sealant, you get a neat, fresh look that complements most bathroom and kitchen colour schemes, blending effortlessly for a seamless seal. Plus, this white bathroom silicone is super easy to use, making it perfect for DIYers, offering a reliable seal with minimal effort. 

Suitable materials: Glass, stainless steel, ceramics, plastic baths and fittings, and most non-porous surfaces commonly found in kitchens and bathrooms. 

Sizes: 280ml. 

Coverage: Approx. 11m of a 5mm bead per cartridge. 


HOW TO USE

PREPARATION 

1. Joint surfaces must be sound, clean and free from contaminants such as dust, oil, grease and any loose material. 

2. If desired, place masking tape along the joint edges before application.  

APPLICATION 

3. Unscrew the nozzle, and using a sharp knife, carefully cut off the dome of the white bathroom sealant, taking care not to damage the thread. Screw the nozzle on to the cartridge. 

4. Cut off the tapered end of the nozzle at a 45° angle, to a width matching the gap to be sealed. 

5. Fit the cartridge into the cartridge gun by pressing the release plate and pulling out the plunger. Insert cartridge and repeatedly squeeze the trigger until the sealant appears. 

6. Place the nozzle at the start of the gap and gently squeeze the trigger. Push forward slowly, ensuring that contact is made by the sealant with both sides of the gap. At the end of the run, release the trigger and press the plunger release plate of the gun. 

7. Smooth the sealant with a wet, round ended tool (do not use a wetted finger), remove any excess with a cloth moistened with white spirit and then remove the masking tape (if used) from either side of the bead. 

8. After use, ensure to wipe away any excess sealant from the nozzle. Replace the cap. 

HOW TO REMOVE

  • Uncured sealant: Excess uncured sealant should be removed carefully using a soft scraper. The remainder can be removed using a cloth moistened with white spirit. Repeat using another clean cloth moistened with white spirit. 
  • Cured sealant: There is no adequate solvent; carefully cut away excess with a very sharp knife. Do not use solvent to remove product from skin – use soap and water. 

FAQs

EVO-STIK Bathroom and Kitchen Sealant should form a skin within 15 to 60 minutes, dependent on bead width, temperature and humidity. For optimum performance, it may take up to one week to dry all the way through.

There is no adequate solvent to remove this sealant. Carefully cut away excess with a very sharp knife. Do not use solvent to remove product from skin – use soap and water.

Yes - it forms a durable, flexible seal that will prevent both leaks and draughts.

Yes - as it is water-based, EVO-STIK Bathroom and Kitchen Sealant sets by the evaporation of water out of the  sealant and so there will be some shrinkage.

Video

Video Url